|
Thumbnail |
Description |
Price |
 |
Custom Trigger return spring kit. This is a replacement spring and screw
that will reduce your trigger pull dramatically. The original
Remington trigger return spring is very heavy/strong and contributes to an
overly heavy trigger pull. The function of the trigger return spring is to
simply return the trigger to a position that will allow it to engage the
hammer sear notch. This kit is the simplest method to dramatically reduce
trigger pull on the rolling block rifle. This kit is for the large frame
military actions both #1 and #5 models. This kit is not made for the #2,
#4, or #6 rifles. Spring only $10 |
$15 |
|
|
Hollow hex head barrel band screw. This screw fits the front band on the
#5 military rifle and the middle band on the late #1 three band military
rifle. They are hollow to allow the installation of the sling swivel through
the screw. This is a new manufacture steel part that will blue or brown
to match your rifle. |
$6.00 |
|
|
Barrel Band Screw. This is the screw for the rear band
on the #5 military rifle. It also fits the front and rear bands of the
late #1 military rifles. This is a new manufacture part furnished in the
white. |
$6.00 |
|
|
Tang Screw- Gunsmith repair tapered Tang Screw. This is a tang screw for
a large frame rolling block receiver (including #1, #1 1/2, #5 and
similar size sporting models). It is identical to the original tang
screws except we threaded it 1/4-28. This allows a gunsmith to re-tap
the tang screw hole on a trigger guard 1/4-28 and use this aftermarket
screw as opposed to obtaining a custom tap in #14-26 to restore the
original thread pattern where the trigger guard tang screw hole has been
damaged. For those wanting to do an original restoration we also have the custom
#14-26 tap see below. |
$10 |
|
|
Special Tap ground #14-26 for the tang screw hole in a large frame rolling
block trigger guard (both sporting and military models). This tap was ground
to match the original #5 tapered Tang Screw, (see the #5 RB page). This tap
is made in the USA as are all of our parts. If you are doing an accurate
restoration we are likely the only source for this tap today. |
$50 - S&H $1.50 |
| |
Special Tap. #11-28 for large frame receiver Guard Screw and Main Spring Screw holes. Also has #4 applications |
$35 |
| |
Cleaning rod for the Danish model Remington rolling block This is a
reproduction of the Danish 1867 cleaning rod. 34 5/16 long with the
proper fine thread bottom end for the early cylinder style cleaning rod
stop. It is furnished in the
white and can be finished to match your particular rifle.
Have a special need - Call us, we may be able to make
a custom cleaning rod for your application |
$35 - $5.55 S&H |
| |
Cleaning Rod for the New York State Militia Rifle. This
is a
reproduction of the NY State cleaning rod with the proper course thread
bottom end to screw in to the cleaning rod stop. This rod is furnished
in the white. |
$35 - $5.55 S&H |
| |
Cleaning rod for the 1879 Argentine rolling block rifle. This rod is a
reproduction of the cleaning rod for the three band Modelo Argentino
1879 Rifle. The rod is 34 inches long and has the appropriate course
thread a the bottom end to fasten into the cone style cleaning rod stop.
This rod is also correct for most other .43 cal #1 three band military rifles. |
$35 - $5.55 S&H |
|
|
Cleaning rod for the 1871 Springfield Army contract rifle caliber .50-70. This repro rod is the double shoulder rod that was only furnished with the 1871 model of Remington's rolling block rifles. See Hosmer's book chapter 15 (available from our references page). |
$40.00 - S&H $5.55 |
| |
Original cleaning rod for the Swedish 8x58R military rifle. This rod is 30 1/2 inches long with a slotted tip for the patch and fine thread bottom for the cleaning rod stop. |
$35- $5.55 S&H |
|
|
This is a reproduction cleaning rod made by Bill Wescombe for #5 smokeless powder
cartridge Remington rolling block military rifles. This rod is 28 7/8
inches long and threaded on the back end to screw into the rifle's ram
rod stop. It is furnished in the white so it can be finished to match
your rifle. |
**Out of Stock** |
 |
Butt Plate for the #6 Remington falling block boys rifle.
We have two varieties available; a plain plate without logo for the
earliest production rifles, and another with logo for the mid production
#6 rifles. The logo is 'Remington' over 'UMC' inside a circle with
'trademark' lettering under the circle. This is the variation with UMC
lettering that has larger/taller letters than the Remington. These butt
plates are blued steel. We plan to make the late production variation
butt plate this year (2009). The mounting screws are a #9 slotted
oval head wood screw (see below). These screws are available for $6 a set when
ordered with the butt plate. Please advise which butt plate variation
you want when ordering. |
$30, $2.50 S&H |
| |
Butt Plate Screws for the #6 Remington falling block Rifle. This is a
set of two screws. They are a #9 oval head steel wood screw copied from
some original parts. Have loose, oversize, or
stripped holes, we have #10 screws with the heads turned back to #9 size
that may be the answer. |
$6 each or $10 set |
| |
Spanner Wrench for the rear sight screw on the Transition Models and
1871 Army rifles. This is the sight screw head with the two little holes
instead of the the more modern slot. We also have some original screws
for these applications. |
$8.50 |
| |
Late takedown #4 rifle Butt Plate Screw Set. This is a set of two
screws for the round barrel takedown #4 rolling block rifle. They are #9
steel oval head wood screws. (deeper head than the #6 above) This set
will not fit the earlier production #4 butt plates (rifles with
the tapered octagon barrels.) |
$10 set or $6 each |
| |
Roller Main Spring for the 1871 Army and target rifles. Bill used to make up these springs. At the
time of purchase there were a few of the original unfinished springs in
the inventory that did not have the roller device installed. We recently
had the springs annealed, shaped, rollers added and then re-heat treated.
These springs have each been installed in a #1 receiver and tested for
function. |
**Out of Stock** |
|
|
This is the mounting screw for a #1 Remington rolling block carbine rear
sight. (sight available on the sights page) |
$6.00 |
