Remington Rolling Block Accessories
|
Thumbnail |
Description |
Price |
| Custom Trigger return spring kit. This is a replacement spring and screw that will reduce your trigger pull dramatically. The original Remington trigger return spring is very heavy/strong and contributes to an overly heavy trigger pull. The function of the trigger return spring is to simply return the trigger to a position that will allow it to engage the hammer sear notch. This kit is the simplest method to dramatically reduce trigger pull on the rolling block rifle. This kit is for the large frame military actions both #1 and #5 models. This kit is not made for the #2, #4, or #6 rifles. Spring only $10 |
$15 |
|
|
Hollow hex head barrel band screw. This screw fits the front band on the #5 military rifle and the middle band on the late #1 three band military rifle. They are hollow to allow the installation of the sling swivel through the screw. This is a new manufacture steel part that will blue or brown to match your rifle. |
$6.00 |
|
|
|
Barrel Band Screw. This is the screw for the rear band on the #5 military rifle. It also fits the front and rear bands of the late #1 military rifles. This is a new manufacture part furnished in the white. |
$6.00 |
|
Tang Screw- Gunsmith repair tapered Tang Screw. This is a tang screw for a large frame rolling block receiver (including #1, #1 1/2, #5 and similar size sporting models). It is identical to the original tang screws except we threaded it 1/4-28. This allows a gunsmith to re-tap the tang screw hole on a trigger guard 1/4-28 and use this aftermarket screw as opposed to obtaining a custom tap in #14-26 to restore the original thread pattern where the trigger guard tang screw hole has been damaged. For those wanting to do an original restoration we also have the custom #14-26 tap see below. |
$10 |
|
|
|
Special Tap ground #14-26 for the tang screw hole in a large frame rolling block trigger guard (both sporting and military models). This tap was ground to match the original #5 tapered Tang Screw, (see the #5 RB page). This tap is made in the USA as are all of our parts. If you are doing an accurate restoration we are likely the only source for this tap today. |
$50 |
| Special Tap. #11-28 for large frame receiver Guard Screw and Main Spring Screw holes. Also has #4 applications | $35 |
|
|
Cleaning rod for the Danish model Remington rolling block This is a
reproduction of the Danish 1867 cleaning rod. 34 5/16 long with the
proper fine thread bottom end for the early cylinder style cleaning rod
stop. It is furnished in the
white and can be finished to match your particular rifle.
Have a special need - Call us, we may be able to make a custom cleaning rod for your application |
$35 - $5.80 S&H | |
| Cleaning Rod for the New York State Militia Rifle. This is a reproduction of the NY State cleaning rod with the proper course thread bottom end to screw in to the cleaning rod stop. This rod is furnished in the white. | $35 - $5.80 S&H | |
| Cleaning rod for the 1879 Argentine rolling block rifle. This rod is a reproduction of the cleaning rod for the three band Modelo Argentino 1879 Rifle. The rod is 34 inches long and has the appropriate course thread a the bottom end to fasten into the cone style cleaning rod stop. This rod is also correct for most other .43 cal #1 three band military rifles. | $35 - $5.80 S&H | |
|
|
Cleaning rod for the 1871 Springfield Army contract rifle caliber .50-70. This repro rod is the double shoulder rod that was only furnished with the 1871 model of Remington's rolling block rifles. See Hosmer's book chapter 15 (available from our references page). |
$45.00 - S&H $5.80 |
| Original cleaning rod for the Swedish 8x58R military rifle. This rod is 30 1/2 inches long with a slotted tip for the patch and fine thread bottom for the cleaning rod stop. | $35- $5.80 S&H | |
|
|
Cleaning Rod #5 7mm Hand fordged as original reproduction. |
**35.00-5.80 S&H** |
| Butt Plate for the #6 Remington falling block boys rifle. We have two varieties available; a plain plate without logo for the earliest production rifles, and another with logo for the mid production #6 rifles. The logo is 'Remington' over 'UMC' inside a circle with 'trademark' lettering under the circle. This is the variation with UMC lettering that has larger/taller letters than the Remington. These butt plates are blued steel. We plan to make the late production variation butt plate this year (2009). The mounting screws are a #9 slotted oval head wood screw (see below). These screws are available for $6 a set when ordered with the butt plate. Please advise which butt plate variation you want when ordering. |
$30, $2.50 S&H |
|
| Butt Plate Screws for the #6 Remington falling block Rifle. This is a set of two screws. They are a #9 oval head steel wood screw copied from some original parts. Have loose, oversize, or stripped holes, we have #10 screws with the heads turned back to #9 size that may be the answer. | $6 each or $10 set | |
| Spanner Wrench for the rear sight screw on the Transition Models and 1871 Army rifles. This is the sight screw head with the two little holes instead of the the more modern slot. We also have some original screws for these applications. | $8.50 | |
| Late takedown #4 rifle Butt Plate Screw Set. This is a set of two screws for the round barrel takedown #4 rolling block rifle. They are #9 steel oval head wood screws. (deeper head than the #6 above) This set will not fit the earlier production #4 butt plates (rifles with the tapered octagon barrels.) | $10 set or $6 each | |
| Roller Main Spring for the 1871 Army and target rifles. Bill used to make up these springs. At the time of purchase there were a few of the original unfinished springs in the inventory that did not have the roller device installed. We recently had the springs annealed, shaped, rollers added and then re-heat treated. These springs have each been installed in a #1 receiver and tested for function. | **Out of Stock** |
Payment may be made by check or money order payable to G. S. Womack, 7343 Annette Ave. Fallon, NV 89406
