Swede Rolling Blocks
The Scandinavian rolling blocks include; the 1868 Remington contract, the 1st production was Remington marked on the tang, has locking screws, chambered 12.17x44R rim fire. The wood and furniture is typical Remington pattern. There are not many of these left in their original form as most were converted to center fire and may more later converted again to 8x58R Danish smokeless in 1889. The second contract was for actions only. These rifles were then finished with various musket and rifle parts in four separate arsenals. The Swede rifles are usually identified by the locking screws used to retain the receiver pins. On the military rifles the locking screws are found on the left side of the receiver adjacent to the individual pins much like Mauser locking screws. Carl Gustav began using the Reminton style button instead of locking screws about 1875. Some of the civilian models have cap screws threaded into the opposite end of the pins (seen from the right side of the receiver). The 1889 breech blocks have a long paddle type thumb piece. While we will be happy to assist you with information regarding the function of the Swede receivers as best we can, we do not have adequate detail regarding the many variations of these rifles needed for collectors of Original firearms. We would refer you to www.skydevaaben.com or [email protected].
|
|
Part # |
Description |
Price |
- |
Button, Pin Retainer Plate Buttons can be seen on some Swedish rifles after 1875 |
$20 |
- |
Button Mounting Screw ($3 when ordered with button) |
$6.00 |
- |
Locking Screw for Hammer and Breech Block Pins (Swede Military) |
$10.00 set of 2. $6.00 each |
- |
Extractor Retaining Screw (Dane and some Swedish Models) |
$6.00 |
- |
Main Spring |
$30.00 |
- |
Main Spring Mounting Screw ($3 when ordered with mounting screw) |
$6 |
- |
1868 Remington Cleaning Rod. We will also make a custom cleaning rod for Swedish model military rifle in 12mm cut to your specified length |
$40.00 $25 Ship |
- |
Original Cleaning Rod for the 8x58R military rifle. This rod is 30.5 inches long with slotted tip for the patch and fine machine threaded bottom to fit the rod stop. |
$35.00 $25 Ship |
- |
Guard Screw - military also fits some Swedes |
$10.00 set, $6.00 each |
- |
Tang Screw, this is a 15/64-26 tapered screw. Individual military trigger guards vary enough the safer part to order is the #5 tang screw. Some civilian production Swedish models do not use this screw. |
$10.00 |
- |
1889 Swede forend cross-blot and Escutcheon |
POR |
- |
1889 Swede extractor mounting screw. NOS |
$6.00 |
- |
1889 Swede extractor NOS For building custom rifles this fits the .45-70 case head nicely. |
$40.00 |
- |
1889 Swede firing pin 12mm rifles converted to center fire. This firing pin makes a nice conversion from the Large BPC tip to a more modern small tip firing pin. Principly used for bushing worn breech block faces |
$20.00 |
- |
1889 Swede firing pin NOS |
$25.00 |
- |
Trigger** |
$35.00 |
- |
Locking Lever** may require gunsmith fitting |
POR |
Sporting model Receiver Pin with matching cap screw for the Breech Bock or Hammer |
$20 |
|
Value |
Original thread pattern Cap Screw for the sporting model receiver pin. These are the most common thread pattern for both Hammer and Breech Block pin. |
$6.00 |
When ordering the above parts please order by the part description. The part numbers are for illustration only and do not reflect any inventory control number. Shipping for the parts above will be charged as $5.50 for the first part and an additional .50 for each additional part except where noted otherwise.
Payment may be made by check or money order payable to Kenn Womack, 7343 Annette Ave. Fallon, NV 89406
Payment may be made by check or money order payable to Kenn Womack, 7343 Annette Ave. Fallon, NV 89406